shear的例句（shear在句子中的用法）

• The novel - flocculant poly - nucleate aluminum hydroxy silicate - sulphate ( PASS ) was prepared and polysilicic acid under non - high shear condition. 在非高剪切力条件下,将硫酸铝引入到聚合硅酸中合成了新型聚硅酸硫酸铝 ( PASS ) 絮凝剂.
• Textbooks commonly denote shear stresses by the symbol and two subscripts. 教科书通常用符号和两个脚标表示剪应力.
• Slitting knives are used to shear the fabric to a precise width. 横切刀被用来将布剪裁到精确的宽度.
• The results showed that starch pastes owned pseudoplastic and the shear - thinning characteristics. 结果表明:所有的样品糊均呈现假塑性流体特征.
• Abstract: Shear force is interrelating with width and thickness of plate and obliquity of knife - edge. 文摘: 斜刃剪切时,剪切力的大小与板料的宽度、厚度及斜刃倾角有关.
• Shear force is interrelating with width and thickness of plate and obliquity of knife - edge. 斜刃剪切时,剪切力的大小与板料的宽度、厚度及斜刃倾角有关.
• There may be widespread changes in ground elevation as well as horizontal or shear displacements. 地面标高可能发生广泛的变动,也可能发生水平位移或剪切位移.
• Shear fracturing effect is attributed to the fact that melt is atomized. 认为剪裂效应是熔体被雾化的根本原因.
• Extensive through - thickness shear causes crack - tip necking. 大范围的穿透厚度剪切引裂纹顶端的颈缩.
• Normally the shear velocity is about half of the compressional velocity. 一般地说横波速度大约是纵波速度的一半.
• It is genetically a metamorphic deposit controlled by shear zone. 400℃,矿床属剪切带型中温变质热液成因.
• Sheet Metal , Metalworking Guillotine , Shear, Bend Shear , New , Used, Machinery Sheet Metal. 采购产品金属板材, 金属加工(剪切, 弯曲)机械钣金.
• The metallocene is summarized as strata, lithology, structure, and especially brittle - ductile shear zone. 该区金矿的控矿条件为地层岩性和构造, 特别是脆 - 韧性剪切带.
• As compared with Shear Type KR Vessel , FWACTV raises the efficiency of agitated mixing. 与“剪切型”的KR法相比, 这种反应器提高了混合效率.
• Objective To study and shear bond strength of resin - reinforced glass ionomer cement ( RGIC ) on orthodontic brackets. 目的探讨两种树脂加强型玻璃离子水门汀对托槽粘结强度的影响.
• Indirect Methods: To measure the interface bond strength include the interlaminar shear strength test. 测量界面粘结强度的间接方法包括层间剪切强度试验.
• Ambitious attempts to improve interlaminar shear strength have been made by Mueller Prosen and by Keogh. 米勒·普罗森还有基奥都对提高层间切变强度作了大胆的尝试.
• The interfacial shear stress is a constant proportion of the bottom shear. 交界面的剪力与底部剪力之比是常数.
• The paper analyes interation shear , fluid forming process , and discuss the ore forming mechanism. 并在此前提下提出了构造-流体-岩石相互作用的金成矿机理.
• In general, the deformation of the model grille is a combination of axial and shear strains. 一般情况下, 模型栅格的变形是轴向应变和切向应变的组合.